Scrap MG bracelet attempt 2

 I decided to have another go with the Scrap MG tutorial I bought from Tonja Lenderman, you can get yours here. I would recommend it Tonjas bracelets are beautiful and her instructions are clear, a great way to turn a pile of scrap into something beautiful.

I made one before which was beautiful but far too big and then I was careless and broke it. I can't tell you too much about what I did as obviously that wouldn't be fair to Tonja but this time I measured the widest point of my hand and measured the bangle to be the same size.

Starting pile of scrap

The finished Scrap MG Bracelet - the one on top, subtle colours

 I was pretty pleased with how it looked. The colours came out a bit subtle compared to my normal colours but I thought it would go brilliantly with my new grey T- shirt with lots of coloured patterns - very similar to the bracelet. I went to try it on - wouldn't ft! But I measured! I tried again ...

OK so it really wouldn't fit over my hand :(

It was too small and I pulled it apart along the join which I had smoothed over but clearly not well enough. So back to the drawing board with bracelet measurements. I will see if I can super glue this one to give to someone with smaller hands!

I feel a bit like Goldilocks, the first one was too big, the second one was 2 small, lets hope the 3rd one will be just right!

Faux Turquoise so far

I tried one of the methods of faux turquoise where you chop the clay (I used my blender) and then reform it, painting on black acrylic paint after baking then sanding so that the black remains  in the cracks.

I used my turquoise ring to match the colour and decided it wasn't a uniform colour so made a shade and a tint of my original turquoise colour, chopped them all in the food processor

I combined all the colours and grated some cured black clay to add as the inclusion

I formed some chip beads from a small pile of clay and rolled in in the black clay gratings I had spread out with a paint brush so there weren't too many on each bead.

Forming a large coin bead using a solid clay core

The coin bead covered

Baking the beads (I decided I needed to get some proper wires sorted when I took this picture!)

A chip bead baked and covered in a layer of black acrylic paint.

Close up of faux turquoise chip bead after painting and sanding

 
 I tried sanding before the black paint was completely dry (it seemed dry on the outside but was still a bit wet in the cracks). This meant the black was a little washed off and the cracks quite deep. I wanted to sand the larger beads and the spoon (there always has to be a cutlery handle somewhere ;) flat and smooth so would need to fill the cracks in with black. I need to go back and try adding some more paint and letting it dry properly this time! I also wondered about mixing some paint with some liquid kato. I'll try and have another go later in the week and let you know how it worked out.

Faux turquoise selection

 I thought I would give the other method I know a go too. You chop the clay the same but apply black acrylic paint before forming and baking.  Unfortunately my bead fell apart whilst sanding :( The instructions said to let the paint dry but on reflection they then used the black chips to cover a clay core and I just mushed some together. I guess they may have stuck to the clay core but didn't have enough stick to stick to each other due to the paint.

Watch out for my next attempt to master the faux turquoise!

Textured Beads, mini tutorial

I have been admiring peoples textured beads for some time and wanted to make some of my own. I tried rolling beads on some rough sandpaper but there wasn't enough texture and I kept rolling the texture I made off and getting bits of sand on my beads - not good. I asked for help from some more experienced clayers - on PCC forum and I also emailed some people direct who had photos of textured beads on flickr. Many people were very generous sharing their techniques - I love the polymer clay world!

Bettina suggested rolling beads between two pieces of rough sandpaper in your palms but I wasn't happy with my sandpaper. I will try that when I have some coarser, clean sandpaper.


The suggestion I am currently using is from Ayelet (you may remember I reviewed her Ayelet Beads tutorial sometime back). I have prepared a mini tutorial for you (although I am sure you could all work it out without the pictures, I had the camera handy). Enjoy!

You will need a ball of clay, a fine grater (this is a nutmeg grater) and a piercing tool (I have a needle tool)

Roll the ball around on the grater

Check it for bald spots, reapply to the grater starting in this spot

Pierce the ball and reroll on the grater to rough up any smooth spots you made whilst piercing (I texture before piercing so it is textured all over or you wouldn't have texture right up to the holes)

I was going to get another flat grater as it would be easier to roll the beads on it but then realised the curve allows you to touch up the top and bottom of the bead whilst on the needle tool.

The finished (nutmeg grater) textured bead.

new toy

My husband has bought himself a new dremel because he needs it to do something in the loft, it's a posh cordless one! When he was ordering all the bits he needed he also ordered a dremel workstation for me (he has been in charge of drilling holes in beads so far). So the quest to master dremel buffing will resume but should be easier cause I can use both hands. Any tips for using this set up gratefully recieved.

New set

 I made myself a new necklace to go with some new clothes my mum kindly bought me. I have another one planned with a series of different beads but need to make some more green flower canes first. I was having trouble getting texture on my beads but with help from some friends on Poymer Clay Central and Flickr I am now happy with them. I used my nutmeg grater in the end to get the texture (need to get a new one now before I need nutmeg again but clay is more important ;)

Necklace and bracelet set

Close up of spliced flower cane bead and the textured beads.

I am going away for a girly weekend and have my lovely new outfit on and feel very smart with my coordinating jewellery! Have a good weekend all.

Dorset Fruits cake forks finished

Finally got round to photographing these cake forks. They are a bit different from my normal style being made to match my sister in laws crockery (not the same one who got the paisley cake forks in case you were wondering).

They are being delivered at the weekend, I hope she likes them!

Crochet hooks

Happy birthday mum!

She has already opened these so I can now show you what I have been busy doing. I didn't give her all these, mum got the four on the right, the larger sizes as I knew she already had many of the smaller ones. I am using the blue one in the middle and it is lovely to work with. So much nicer to hold than the plain aluminium handle.

 I've been busy but look forward to having a bit more time to blog again soon.
Cara